A whirlpool addition — also called a hop stand — is a dose of hops added after the boil has finished but before the wort is chilled. The hops steep in hot wort for a set time, then you chill and transfer as usual.
Why it works
Hop oils evaporate at boiling temperatures, so hops boiled for a long time lose most of their aroma. Below boiling, the oils hang around much longer. At the same time, isomerisation — the process that makes hops bitter — slows dramatically as the temperature falls.
Hold hot wort in the right temperature window and you extract lots of oil and flavour while adding relatively little bitterness.
Temperature decides the result
| Whirlpool temperature | What you get |
|---|---|
| 90–100 °C (straight after flameout) | Strong flavour, plus noticeable bitterness |
| 80–85 °C | Good flavour and aroma, modest bitterness |
| 70–80 °C | Mostly aroma and flavour, very little bitterness |
| Below 70 °C | Aroma, but extraction slows and you're close to a dry hop |
For most pale ales and IPAs, 75 to 80 °C is a good target. It's hot enough to extract well and cool enough to keep added bitterness low.
How to do it
- Turn off the heat at the end of the boil.
- Drop the temperature to your target. An immersion chiller for a few minutes is the quickest. Without one, leave the lid off and wait — it takes 10 to 15 minutes for 25 litres to fall from boiling to around 80 °C.
- Add the hops and stir to create a whirlpool, or just give it a good mix.
- Hold for 20 to 30 minutes, lid on, stirring occasionally.
- Chill to pitching temperature and transfer.
Stirring the wort into a whirlpool also piles hop debris and protein into a cone in the centre of the kettle, which makes it easier to leave the sludge behind when you drain.
How much to use
Whirlpool additions are often the biggest single hop addition in a modern hoppy recipe.
- Pale ale — 2 to 4 g per litre, so 50 to 90 g in 23 litres.
- IPA — 4 to 6 g per litre, so 90 to 140 g.
- Hazy IPA — up to 8 g per litre.
Does it add bitterness?
Some. Brewing software usually estimates whirlpool bitterness as a fraction of what a 60 minute boil would give, depending on the temperature and time. At around 80 °C for 20 minutes, the contribution is small but not zero. If your beers come out more bitter than planned, a whirlpool addition at too high a temperature is a likely suspect.
No-chill and cube hopping
No-chill brewing is popular in Australia: instead of chilling, you pour the hot wort into a sealed plastic cube and let it cool overnight. The catch is that the wort stays hot for hours, so any hops in it keep isomerising.
Two things follow.
- Late boil additions behave like longer additions. A 10 minute addition in a no-chill batch can give the bitterness of a 20 or 30 minute addition. Many brewers simply shift their late additions about 20 minutes later — so a "10 minute" addition goes in at flameout.
- Cube hopping — adding hops directly into the cube — gives flavour and some bitterness. Treat it roughly like a 20 minute boil addition when you calculate IBU.
Aroma from no-chill beers is usually softer than from chilled ones, since the oils have hours to escape. A dry hop puts it back.
Choosing whirlpool hops
Any aroma hop works, but varieties rich in oil shine. Galaxy, Vic Secret, Ella and Eclipse all make excellent whirlpool hops, as do many American and New Zealand varieties. The Australian hops guide has suggestions, and we're always happy to talk through what's fresh in the freezer.
Whirlpool and dry hop together
The best hoppy beers usually use both. The whirlpool gives flavour that sits deep in the beer; the dry hop puts bright aroma on top. A common split for an IPA is about 40 percent of the late hops in the whirlpool and 60 percent in the dry hop.