Mash temperature is the biggest single lever on how fermentable your wort is. Around 64 to 65 °C gives a dry, light-bodied beer; 68 to 69 °C gives a fuller, sweeter one. Miss your target by three degrees and you've brewed a different beer from the one you planned.
Start with the thermometer
Most "I can't hit my mash temperature" problems are actually "my thermometer is wrong" problems.
- Check it in iced water. Fill a glass with crushed ice and a little water, stir, and wait a minute. It should read 0 °C.
- Check it in a rolling boil. On the South Coast, near sea level, water boils at very close to 100 °C.
- Know its offset. If it reads 1.5 °C high, either recalibrate it or write the correction on it in marker.
Digital probe thermometers are faster and easier to read than dial types. Whatever you use, check it a couple of times a year.
Calculate your strike temperature
Cold grain pulls the temperature of the water down. How far depends on how much water there is per kilo of grain, and how cold the grain is. The formula is:
Strike temperature = target + 0.41 ÷ ratio × (target − grain temperature)
where the ratio is litres of water per kilo of grain.
Example: 5 kg of grain at 20 °C, mashed at 3 L/kg (15 litres), with a target of 66 °C.
- Target minus grain temperature: 66 − 20 = 46.
- 0.41 ÷ 3 = 0.137.
- 0.137 × 46 = 6.3.
- Strike temperature = 66 + 6.3 = 72.3 °C.
Brewing software does this for you, but it's worth understanding so you can sanity-check it.
Account for the grain's temperature
This is the step people skip, and on the South Coast it matters. Grain stored in a garage might be 30 °C in February and 10 °C in July. Using the same example, that changes the strike temperature by nearly three degrees. Measure the grain, or at least use a realistic guess for the season.
Account for the mash tun
The formula assumes the vessel doesn't absorb heat. A cold esky or stainless tun does. Two ways to deal with it:
- Preheat it. Fill it with hot water for ten minutes, tip that out, then add your strike water.
- Overshoot and stir down. Add strike water a few degrees hotter, let the vessel warm, then stir with the lid off until it reaches the strike temperature before adding grain.
Once you've brewed a few times with the same gear, you'll know your system's correction. Write it down.
Mix it properly
Add the grain to the water — not the other way round — and stir thoroughly for a couple of minutes, breaking up every dry clump. Dough balls aren't just lost sugar; they hold pockets of cooler grain that throw out your readings.
Wait five minutes, then check the temperature in three or four places. If the readings differ, keep stirring.
Correcting a miss
Too hot: stir with the lid off, which drops it quickly. For a bigger correction, add cold water or a few ice cubes, a little at a time. A degree or two over for the first few minutes does little harm. An hour over does.
Too cold: add boiling water a litre at a time, stirring and rechecking. In an urn or all-in-one system, apply gentle heat while stirring, keeping the bag clear of the element.
Holding it for an hour
- Insulate. A blanket or a sleeping bag around the vessel makes a huge difference.
- Keep the lid on between checks.
- Expect some loss in winter. An unheated garage in a South Coast July can pull a poorly insulated mash down several degrees in an hour. Check halfway and correct.
- Recirculating systems hold temperature on their own. Make sure the probe is reading the mash, not just the liquid near the element.
Keep notes
Record strike temperature, grain temperature, water volume and the temperature you actually landed on. After three or four brews, the numbers for your gear will be predictable. If you're consistently missing in one direction, bring your notes in and we'll find the reason.