At some point every all grain brewer goes looking for their water report, finds a PDF full of microbiology counts and metals at the limit of detection, and closes it again. The information you need is usually in there. It just isn't labelled for brewers.

Finding the report

Shoalhaven Water publishes monthly test results for the reticulated supply on its drinking water quality page. Most councils and water utilities publish something similar, and if yours doesn't, a polite email usually gets you one.

On tank or bore water there's no report to find, so you'll need a lab test. NATA-accredited labs will test for the minerals below for a modest fee, and one test is enough — tank water doesn't change much once you know what you're dealing with.

The units

Almost everything is in mg/L, which is the same as ppm (parts per million) in brewing software. The catch is that hardness and alkalinity are often reported "as CaCO₃" — as if they were calcium carbonate — rather than as the actual mineral. You need to convert those before entering them.

Report says Multiply by To get
Calcium hardness as CaCO₃ 0.40 Calcium (Ca)
Magnesium hardness as CaCO₃ 0.243 Magnesium (Mg)
Total alkalinity as CaCO₃ 1.22 Bicarbonate (HCO₃)

So a calcium hardness of 40 mg/L as CaCO₃ is 16 mg/L of calcium. An alkalinity of 20 as CaCO₃ is about 24 of bicarbonate. If the report gives calcium and magnesium directly, use those and skip the conversion.

If you only get total hardness, you can't split it exactly between calcium and magnesium. For soft water like Shoalhaven's, at around 50 mg/L total hardness as CaCO₃, assuming most of it is calcium is close enough — that's about 15 to 20 mg/L of calcium.

The six lines that matter

  1. Calcium — usually the most important number for all grain brewers.
  2. Magnesium.
  3. Sodium.
  4. Chloride.
  5. Sulfate.
  6. Alkalinity or bicarbonate — this, more than the water's pH, decides how your water pushes mash pH around.

Two more worth a glance

pH. Interesting, but less useful than it looks. Water pH tells you little about how the water behaves in a mash. Alkalinity does that job.

Free and total chlorine. These tell you what disinfectant you're dealing with. If total chlorine is much higher than free chlorine, part of it is combined chlorine such as chloramine. Either way, a campden tablet takes care of it.

What you can ignore

Microbiology results, turbidity, colour, fluoride, and the long list of metals and organic compounds well under their guideline limits. They matter enormously to the people running the treatment plant and not at all to your mash. The one exception is iron or manganese at unusually high levels, which can taste metallic — but reticulated water is almost never anywhere near that.

Averages, ranges and your tap

Reports show results from several sampling points, often as a range or an average. Figures move with the seasons and after heavy rain, when river water changes character. For brewing, those swings are small. Use a typical value, not the extremes, and don't chase the monthly variation.

Putting the numbers to work

Enter the six values as your source water in your brewing software. From there it can estimate mash pH and calculate salt additions for whatever profile you're aiming at. The water profile guide explains what those additions do, so you can check the software's answer makes sense.

When a line is missing

Sulfate and chloride are the values most often left off. For soft water, both are usually low, and assuming 5 to 10 mg/L each is a reasonable start. If you want certainty, a home water test kit or a one-off lab test fills the gap. For a competition beer where precision matters, many brewers simply use bottled distilled or reverse-osmosis water and build the whole profile from zero.

Keep a copy

Save the report with your brewing notes and record which figures you entered. When a beer comes out better or worse than expected, you'll be able to rule water in or out. And if you'd like a hand turning the report into salt additions, bring it in.