Mid-strength beer is an Australian institution, and for good reason. Long afternoons in the heat, a barbecue that starts at lunchtime, a drive home later. A beer at 3.5 percent that still tastes like proper beer is one of the most useful things a home brewer can make.

Why session beers taste thin

Alcohol contributes to body and warmth, and so does residual sweetness. A low-gravity beer fermented with a dry, highly attenuative yeast finishes thin and watery, and its bitterness can feel harsh because there's so little malt to balance it.

The trick is to build body back in without adding fermentable sugar.

Mash high

Mash at 68 to 69 °C rather than 65 to 66. This favours the enzyme that makes longer, less fermentable sugars, leaving more body and a slightly sweeter finish. It's the single most effective change.

Add body malts

A few grains add body without adding much alcohol.

  • Carapils or other dextrin malts — 5 to 10 percent of the grist. Body and head with little flavour.
  • Oats — 5 to 10 percent. A silky, rounded mouthfeel.
  • Wheat malt — 5 to 15 percent. Body and excellent head retention.
  • Light crystal — a little, for sweetness and body. Keep it modest or the beer turns syrupy.

Choose a less attenuative yeast

Yeasts that leave a little more sweetness behind help a lot. Many English ale strains finish noticeably fuller than clean American strains. Check the attenuation figure on the packet — a strain around 68 to 72 percent will leave more body than one at 78 to 82 percent.

Keep bitterness in proportion

With so little malt, bitterness reads stronger. Aim for a bitterness ratio — IBU divided by gravity points — around 0.5 to 0.7. For a 1.036 beer, that's about 18 to 25 IBU.

Get the hop character from late additions and dry hops rather than early bittering. A session pale ale can carry a generous dry hop beautifully.

Use water for roundness

Calcium chloride adds fullness and a perception of sweetness. A water profile with chloride equal to or a little higher than sulfate helps a session beer feel rounder.

Carbonate a little lower

High carbonation emphasises a thin body. Carbonate session beers to around 2.2 to 2.4 volumes rather than 2.6 or more. Serving slightly less cold also helps the malt come through.

A 23 litre session pale ale

Amount
Pale ale malt 3.2 kg
Wheat malt 300 g
Carapils 200 g
Light crystal 150 g
Mash 68.5 °C for 60 minutes
Clean bittering hop, 60 minutes about 12 IBU
Galaxy or Vic Secret, 10 minutes 15 g
Galaxy and Ella, whirlpool at 80 °C 30 g each
Galaxy and Ella, dry hop 30 g each
Yeast An English ale strain, or a clean strain with moderate attenuation
Water 3 g gypsum + 4 g calcium chloride in ~30 L

At about 72 percent efficiency, that's around 1.037, finishing near 1.011 for about 3.4 to 3.5 percent ABV and roughly 22 IBU. Ferment at 18 °C and carbonate to about 2.3 volumes.

The kit route

A beer kit made up with 1 kg of light dry malt to 23 litres lands at roughly 1.038 and around 3.5 to 4 percent, with much more body than the same kit made with sugar. Add a 10 minute hop boil and a dry hop, and you have a very drinkable mid-strength beer for about an hour's work.

Styles that are session beers by nature

Some styles are naturally low in alcohol and full of flavour.

  • English mild and ordinary bitter — 3 to 3.8 percent, malty and satisfying.
  • Irish dry stout — around 4 percent and full of roast flavour.
  • Session IPA and session pale ale — hop-forward and light.
  • Grisette and table saison — light, dry and spicy.

These are brilliant beers in their own right, not just reduced versions of stronger ones.

Freshness

Low-alcohol beers have less protection against staling and oxidation, so they're at their best young. Brew them, drink them within a couple of months, and brew them again. If you'd like help adapting one of your favourite recipes to mid-strength, bring it in.