Carbonation is measured in volumes of CO₂ — the volume of gas dissolved in the beer, compared with the beer's own volume. A beer at 2.5 volumes holds two and a half litres of CO₂ in every litre of beer.
Levels by style
| Style | Volumes of CO₂ |
|---|---|
| English bitter, mild | 1.5–2.0 |
| Stout, porter | 1.8–2.3 |
| English IPA, brown ale | 2.0–2.4 |
| American and Australian pale ale, IPA | 2.3–2.7 |
| Lager, pilsner | 2.4–2.7 |
| Belgian ales | 2.5–3.5 |
| Saison | 3.0–3.5 |
| Hefeweizen | 3.3–4.0 |
| Sparkling cider | 2.5–3.0 |
Within each range, lighter, crisper beers sit higher and fuller, maltier ones lower. Above about 3 volumes, standard bottles can be at risk — use heavier bottles made for high carbonation.
Bottling: priming sugar
When you bottle, a measured amount of sugar ferments in the bottle to make the CO₂. A useful rule:
About 4 grams of dextrose per litre adds roughly one volume of CO₂.
But the beer already holds some CO₂ from fermentation, and how much depends on the warmest temperature it reached after fermentation finished — warmer beer holds less.
| Beer temperature | CO₂ already in the beer |
|---|---|
| 15 °C | about 1.0 volume |
| 18 °C | about 0.9 volume |
| 20 °C | about 0.85 volume |
| 22 °C | about 0.8 volume |
Example: a pale ale at 20 °C, targeting 2.5 volumes.
- Needed: 2.5 − 0.85 = 1.65 volumes.
- Dextrose: 1.65 × 4 = 6.6 g per litre.
- For 23 litres: about 150 g of dextrose.
Online priming calculators do this instantly and handle other sugars. Table sugar needs slightly less than dextrose; dry malt extract needs more.
Carbonation drops are pre-measured sugar tablets — usually one per 375 mL bottle, two per 750 mL — and give a standard, fairly lively carbonation. They're convenient but less precise. For low-carbonation styles like stout or bitter, batch priming with weighed sugar gives you more control.
Batch priming — dissolving the sugar in a little boiled water and gently mixing it into the whole batch in a bottling bucket — gives more consistent carbonation than adding sugar to each bottle.
Bottles take about two weeks at 18 to 22 °C to carbonate, sometimes longer for strong beers.
Kegging: setting the pressure
In a keg, carbonation depends on pressure and temperature. At a typical fridge temperature of 4 °C, these settings reach roughly:
| Target volumes | Pressure at 4 °C |
|---|---|
| 2.0 | about 6–7 psi |
| 2.2 | about 9 psi |
| 2.5 | about 12 psi |
| 2.7 | about 14 psi |
| 3.0 | about 17 psi |
Set the regulator, leave the keg connected, and the beer reaches that level in about a week. Colder beer absorbs more gas at the same pressure; warmer beer less. A carbonation chart covers other temperatures.
Burst carbonating — setting a higher pressure, around 30 psi, for 24 to 36 hours, then dropping back to serving pressure — gets you there faster. Just don't forget to turn it down, or you'll overshoot.
Choosing within the range
The ranges above are wide, and where you land within them changes the beer.
- Higher carbonation makes a beer feel lighter, crisper and more refreshing, and lifts hop aroma out of the glass. It also adds a little perceived acidity and can make bitterness seem sharper.
- Lower carbonation makes a beer feel fuller, softer and smoother, and lets malt flavours come forward.
So a session ale or a malty English bitter usually wants the lower end, and a crisp lager or a hoppy pale ale the upper end. On a hot day a slightly higher level is more refreshing; for a stout by the fire in July, lower is better.
Checking your results
Open a bottle after two weeks and pour it into a glass. A healthy head that settles to a thin, lasting layer, with a steady stream of fine bubbles, is about right for most ales. Huge foam that won't settle, or beer that gushes from the bottle, means over-carbonation — or, if it gets worse over time, an infection. Flat beer after two weeks at 18 to 22 °C usually means too little sugar, too cold a conditioning spot, or a cap that didn't seal.
Serving problems
Foamy pours usually mean the beer is over-carbonated, too warm, or the beer line is too short for the serving pressure. Longer lines add resistance and slow the pour.
Flat beer usually means too little pressure, a gas leak, or too little time.
If you're chasing a carbonation problem, bring your setup details in — temperature, pressure and line length — and we'll help you work it out.