CO₂ does two jobs in a kegging setup: it carbonates the beer and it pushes it out of the tap. Getting the gas side right is mostly about understanding a few simple parts and keeping everything leak-free.

The cylinder

CO₂ is stored in the cylinder as a liquid under high pressure, with a layer of gas on top. Cylinders are described by how much CO₂ they hold, in kilograms.

Smaller cylinders fit inside a kegerator or a keg fridge and are easy to carry. Larger cylinders last much longer between swaps and work out cheaper per kilo of gas, but usually sit outside the fridge.

How long a cylinder lasts depends far more on leaks than on how much beer you drink. A tight system uses surprisingly little gas. A system with a slow leak can empty a cylinder in a week.

Swap or refill?

You can either swap an empty cylinder for a full one or have your own cylinder refilled.

  • Swapping is quick — bring in your empty, walk out with a full one.
  • Refilling means your own cylinder is filled and returned to you. Handy if you've invested in a particular cylinder.

We do both at the counter in South Nowra. Ask about current swap and refill options when you come in.

Test dates

Gas cylinders have to be periodically inspected and pressure-tested, and the test date is stamped on the cylinder. Refillers won't fill a cylinder that's out of test. If you buy a second-hand cylinder, check the stamp first — a cheap cylinder that needs testing before anyone will fill it may not be such a bargain.

The regulator

A cylinder holds CO₂ at very high pressure — over 800 psi at room temperature. A regulator drops that to a usable pressure for carbonating and serving, usually somewhere between 5 and 30 psi.

Most home brew regulators have two gauges.

The high-pressure gauge shows the pressure inside the cylinder. This is the one that confuses people. Because the CO₂ is liquid, the cylinder pressure stays roughly the same until the liquid has almost all gone. So the gauge reads "full" almost right up until the cylinder is nearly empty, then drops quickly. It's a warning light, not a fuel gauge.

The low-pressure gauge shows the output pressure you've set — your carbonation or serving pressure. Adjust it with the screw or knob on the regulator.

A regulator should also have a pressure relief valve that vents if the output pressure gets dangerously high.

Knowing how much gas is left

Since the high-pressure gauge won't tell you, weigh the cylinder. The empty weight — the tare — is stamped on the cylinder. Weigh the full cylinder on bathroom scales or a luggage scale, subtract the tare, and you know how much CO₂ is inside. Weigh it again later to track how fast you're using it.

Connecting it all up

The usual gas path runs from cylinder to regulator, through a gas line to the keg's gas disconnect. On the common ball-lock kegs, grey disconnects go on the gas post and black disconnects on the liquid post. A check valve in the gas line stops beer flowing back into the regulator if the pressure ever drops — a cheap part that saves an expensive one.

Push-in fittings such as Duotight and John Guest make connecting lines quick and tidy, with no hose clamps.

Finding leaks

Leaks are the number one reason cylinders run out early.

  • Spray every joint with soapy water — cylinder valve, regulator connection, gas line fittings, disconnects and keg posts. Bubbles mean a leak.
  • Check the regulator washer where it meets the cylinder. Replace it if it's worn or flattened.
  • Check keg lid seals and post O-rings. A light smear of food-grade keg lube helps them seal.
  • The overnight test: set the pressure, close the cylinder valve and note the low-pressure reading. If it has dropped by morning, something's leaking downstream.

Safety

CO₂ is safe when handled properly, but it deserves respect.

  • Keep cylinders upright and secured so they can't fall. A damaged valve on a high-pressure cylinder is genuinely dangerous.
  • Never connect a cylinder to a keg without a regulator.
  • Keep cylinders away from heat, including direct sun and hot cars. Pressure rises sharply with temperature.
  • Ventilate. CO₂ is heavier than air and displaces oxygen. A large leak in a small, closed space — a cupboard, a sealed cellar — can be dangerous. Keg fridges in normal rooms are fine.
  • Close the cylinder valve when you're away for a while, or if you suspect a leak.

Keeping your gas side healthy

  1. A cylinder that is in test, kept upright and secured.
  2. A regulator with a working pressure relief valve.
  3. Fresh washers and O-rings, and a spray bottle of soapy water for leak checks.
  4. Gas line with clamps or push fittings in good condition.
  5. A check valve to stop beer flowing back into the regulator.