Of all the variables in a fermentation, how much yeast you pitch is one of the easiest to control and one of the most often ignored. Get it roughly right and fermentation starts quickly, finishes cleanly and stays predictable.

The rule of thumb

Brewers express pitching rates in millions of cells per millilitre of wort, per degree Plato. Degrees Plato is just another way of expressing gravity — divide the gravity points by four. A wort of 1.048 is about 12 °P.

Beer Pitching rate
Ales up to about 1.060 0.75 million cells/mL/°P
Strong ales above 1.060 1.0 million cells/mL/°P
Lagers 1.5 million cells/mL/°P
Strong lagers 2.0 million cells/mL/°P

Working it out

Cells needed = rate × volume in millilitres × degrees Plato.

For a 23 litre ale at 1.048:

0.75 × 23,000 × 12 = 207,000 million, or about 200 billion cells.

The same beer brewed as a lager:

1.5 × 23,000 × 12 = about 415 billion cells.

How much yeast is in the pack?

  • A sachet of dry yeast (11.5 g) — manufacturers typically guarantee at least 6 billion cells per gram, so at least 70 billion per sachet, and real counts are often well above that. In practice, one fresh sachet handles a normal-strength 23 litre ale comfortably.
  • A fresh liquid pack or vial — about 100 billion cells when it's made, falling by roughly a fifth each month it sits in the fridge.
  • Harvested slurry — very roughly 1 to 2 billion cells per millilitre of thick, settled slurry.

So for that 1.048 ale: one fresh dry sachet, or one very fresh liquid pack (slightly under), or a starter. For the lager: two or three dry sachets, or a well-made starter.

What underpitching tastes like

When there's too little yeast, each cell has to do more work, and the yeast spends longer growing before it gets down to fermenting. That stress shows up in the beer.

  • Fruity esters — banana, pear, bubblegum — where you didn't want them.
  • Fusel alcohols — a hot, solvent-like, headache-inducing character.
  • Diacetyl — butter or butterscotch, because stressed yeast doesn't clean up after itself properly.
  • Acetaldehyde — green apple, if fermentation finishes sluggishly.
  • A long lag before fermentation starts — 24 to 48 hours or more — which gives bacteria and wild yeast a window to get established.
  • Incomplete attenuation — the beer finishes sweet and heavy.

If those sound familiar, see the esters, diacetyl and fusels guide.

What overpitching tastes like

It's much harder to overpitch badly at home, and a moderate overpitch is far better than an underpitch. Seriously overpitched beers can taste:

  • Thin and flat, with a muted yeast character.
  • Slightly yeasty or meaty, if lots of yeast dies off.

For styles that depend on yeast character — hefeweizens, many Belgian beers — overpitching can strip out the fruity and spicy notes that make the style. These are the only beers where you might deliberately pitch on the low side.

Pitching is more than cell count

The number of cells is only part of it. Healthy, active yeast needs a few other things.

Oxygen. Yeast needs oxygen at the start of fermentation to build healthy cell walls before it gets down to work. Splash the wort into the fermenter, shake it vigorously, or use an aeration stone. Dry yeast has more reserves and is less fussy, but all yeast benefits.

Temperature. Pitch at or slightly below your fermentation temperature, not into warm wort. Pitching into 28 °C wort and letting it cool down later gives the yeast a warm, fast, flavour-damaging start — and on the South Coast, waiting another hour for the wort to cool is always worth it.

Freshness. Old yeast has fewer living cells and less vitality. Check dates.

Nutrients. All grain worts usually have plenty. Kits with a lot of added sugar, and fruit or honey musts, can benefit from yeast nutrient.

What about the yeast under the kit lid?

Most beer kits come with a small sachet of yeast taped under the lid. It's usually a few grams — less than a standard 11.5 g sachet — and it may have sat on a warm shelf for a long time. It will ferment the beer, but it's often a slight underpitch of a fairly generic strain.

Swapping it for a fresh 11.5 g sachet of a good ale yeast — or a lager yeast if you're brewing a lager kit cold — is one of the cheapest upgrades a kit brewer can make. Fermentation starts sooner, finishes more reliably and tastes cleaner.

Signs you got it right

  • Visible activity within 12 to 24 hours — a layer of foam on the surface, or bubbling.
  • A vigorous ferment for two to four days, then a gradual slowdown.
  • Final gravity in the expected range within a week or so for an ale.
  • A clean aroma from the fermenter — bready, fruity in a pleasant way, maybe a little sulphur for lagers — rather than solvent or nail polish.

If fermentation takes more than a day and a half to show any sign of life, or the beer tastes hot and harsh, look first at how much yeast went in and how warm the wort was when it did.

Rehydrating dry yeast

Manufacturers increasingly say modern dry yeast can be sprinkled straight onto the wort. Rehydrating — sprinkling it into about ten times its weight of lukewarm, sterile water for 15 to 30 minutes first — gives a slightly higher number of healthy cells. For a normal beer, either works. For a big beer or a lager, rehydrating is worth the extra few minutes. Follow the instructions on the sachet for temperature.

Getting the pitch right

  1. One fresh 11.5 g dry sachet for a normal-strength 23 litre ale.
  2. Two sachets for lagers and for ales above about 1.060.
  3. A starter for liquid yeast in anything but a fresh, normal-strength ale.
  4. Aerate the wort well before pitching.
  5. Pitch at fermentation temperature, not warm.