"My beer's stopped fermenting" is one of the most common questions we get across the counter, and most of the time the beer isn't stuck at all. It's either finished, or it's working quietly. A few readings tell you which.
Step 1: stop watching the airlock
The airlock is a terrible measuring device. Bubbles slow down and stop for all sorts of reasons that have nothing to do with fermentation finishing.
- The lid isn't sealed. CO₂ escapes around the seal instead of through the airlock. Very common with bucket fermenters.
- The beer has finished. Most ales are done in five to seven days.
- The temperature dropped. Fermentation slows right down in a cold garage.
- Pressure fermenters and spunding valves don't bubble at all.
The only way to know what's happening is to measure.
Step 2: take two readings, a few days apart
Take a gravity reading with a hydrometer. Take another two or three days later.
- If the gravity is still dropping, fermentation is still going. Leave it alone.
- If it's the same on both days, fermentation has stopped. Now decide whether it has finished or stuck.
If you use a refractometer, remember that alcohol throws off its readings once fermentation starts. You need a correction calculator, or use a hydrometer for these checks. The hydrometer and refractometer guide explains.
Step 3: compare with what you should expect
Typical final gravities:
| Beer | Typical final gravity |
|---|---|
| Kit with dextrose or brewing sugar | 1.004–1.010 |
| Kit with brew enhancer or dry malt | 1.008–1.014 |
| All grain, mashed at 64–66 °C | 1.008–1.012 |
| All grain, mashed at 68–69 °C | 1.012–1.018 |
| Beer with lots of crystal malt or lactose | 1.016 or higher |
If your reading sits in or near the expected range, the beer has finished. It isn't stuck. It just finished higher than you hoped — and that's usually a recipe or mash question, not a fermentation problem.
If it's clearly higher — say 1.025 for a kit beer — keep going.
Step 4: work out why
It's too cold. The most common cause around Nowra between May and September. An unheated garage at 12 °C will stall most ale yeasts. Some English strains drop out of suspension at the first sign of cold.
Too little yeast, or tired yeast. Underpitching, old liquid yeast, or a sachet that sat in a hot car. See the pitching rates guide.
Unfermentable wort. A high mash temperature, a lot of crystal malt, or lactose all leave sugars yeast can't eat. The beer is finished; the recipe just made it that way.
Poor nutrition. Kits made with a lot of plain sugar, and very high gravity worts, can starve the yeast of nutrients.
A temperature shock. A sudden cold snap can send yeast to sleep.
Very high alcohol. Strong beers can exceed the yeast's tolerance.
A flocculent strain that settled early. Some yeasts clump and drop out before they've finished.
Step 5: try the fixes, in this order
- Warm it up. Move the fermenter somewhere around 20 to 22 °C. Many "stuck" ferments restart within a day or two.
- Rouse the yeast. Gently swirl the fermenter to lift the yeast back into suspension, without splashing.
- Wait three to five days and take another reading.
- Add yeast nutrient, if the wort was sugar-heavy. Nutrient helps most early in fermentation, but it can help a sluggish one too.
- Repitch. Add fresh, active yeast — ideally a robust, high-attenuating strain. A rehydrated dry sachet works; better still is a small starter at full activity, because yeast thrown into alcohol without being woken up often struggles.
- Last resort: an enzyme. Amylase enzymes break down unfermentable sugars so the yeast can finish them. They work, sometimes too well — they can ferment the beer much drier than intended. Use with caution, and don't bottle until the gravity has been stable for several days.
Don't bottle a stuck beer
Bottling a beer that hasn't finished fermenting, then adding priming sugar, is the classic way to make bottle bombs. If you're unsure, wait. A few more days in the fermenter costs nothing.
Prevention
- Pitch enough healthy yeast.
- Aerate the wort well.
- Keep the temperature steady and in the yeast's range — and in winter, that may mean a heat belt or a warm room.
- Use malt or brew enhancer rather than plain sugar with kits.
- Take notes, so you know what your recipes normally finish at.
The stuck-ferment toolkit
- A hydrometer and trial jar — the airlock is not a measuring device.
- Yeast nutrient for sugar-heavy worts.
- A spare sachet of a robust, high-attenuating dry yeast.
- A way to keep the fermenter at 18–22 °C through winter.
- Notes: original gravity, mash temperature, yeast and pitch date.