Wort is a perfect food — for yeast, and for every bacterium and wild yeast that drifts past. Your job is to make sure your chosen yeast gets there first and has no competition. That's what sanitation is for.
Cleaning and sanitising are different jobs
Cleaning removes dirt you can see and residue you can't: dried krausen, beer stone, hop gunk, old yeast. Bacteria hide underneath residue where sanitiser can't reach them.
Sanitising kills most of the microbes left on a clean surface — enough that your yeast wins easily.
Sterilising kills everything. You don't need it, and you can't practically achieve it at home.
The order matters: clean first, then sanitise. Sanitiser on a dirty surface is wasted.
Cleaning
- Use a percarbonate-based cleaner — the oxygen cleaners sold for brewing. Dissolve it in warm water, soak equipment for 20 minutes to an hour, and the residue lifts off.
- Use a soft cloth or sponge. Never use scourers or abrasive pads on plastic. Scratches are where bacteria live, and you can't clean or sanitise them out.
- Rinse well after cleaning.
- Clean straight after use. Fresh residue comes off in seconds; dried residue takes a long soak.
- Take taps apart. Fermenter and bottling taps trap old beer and yeast inside. Dismantle, clean and reassemble them every time.
Avoid household detergents with fragrance — they leave residues that kill head retention and can taste soapy. And avoid chlorine bleach unless you rinse very thoroughly with treated water, because chlorine residue causes medicinal flavours (see the chlorine guide).
Sanitising
A no-rinse acid sanitiser is the easiest and most reliable option for home brewers.
- Mix it at the recommended dilution — usually a few millilitres per litre. More isn't better.
- Make sure every surface is wetted and give it the contact time on the label, typically one to two minutes.
- Don't rinse. At the correct dilution, it's food-safe, and the yeast will happily ferment right on top of it.
- Don't fear the foam. These sanitisers foam. The foam is harmless and doesn't affect the beer. Tip out the excess and get on with it.
- Keep a spray bottle of it mixed up for quick jobs — the airlock, the lid seal, the scissors that open the yeast sachet, the outside of the yeast packet.
Mixed sanitiser keeps for a while in a sealed container, but it weakens over time and in hard or contaminated water. If it turns cloudy, mix a fresh batch.
What needs sanitising
The rule is simple: anything that touches the wort or beer after the boil.
- Fermenter, lid, airlock, grommet and tap
- Anything used to stir or aerate cooled wort
- The hydrometer and trial jar, if the sample goes back in (better not to return it)
- Siphons, tubing and bottling wands
- Bottles, caps and kegs
- Your hands, or gloves, if they're going to touch anything
What doesn't
Anything used before or during the boil — the mash tun, the kettle, the mash paddle, the bag. The boil sanitises the wort itself. Clean these thoroughly, but there's no need to sanitise them.
Bottles
Bottles are where many sanitation problems start, because there are so many of them.
- Rinse every bottle straight after pouring. Two or three hot-water rinses stop sediment drying in.
- Store them dry and upside down, or capped with foil.
- Inspect them before bottling. Any with stubborn residue get a soak in cleaner and a brush.
- Sanitise them on bottling day. A bottle rinser or a bottle tree makes this fast.
Replace what you can't clean
Plastic scratches, seals perish and taps wear out. A scratched fermenter or a cracked tap is a permanent home for bacteria. Replace them — they're cheap compared with a run of infected batches.
How to tell if sanitation has failed
Signs of infection include a sour or vinegary smell, a film or ropey strands on the surface, beer that keeps getting thinner and drier in the bottle, gushing bottles, and medicinal or band-aid flavours. Some infections are subtle and show up only after weeks in the bottle.
If you're unsure, bring a bottle in. We'll taste it with you and help track down the cause.
A complete cleaning kit
- A percarbonate-based cleaner for removing residue.
- A no-rinse acid sanitiser for everything that touches cooled wort.
- A spray bottle of mixed sanitiser for quick jobs.
- Soft cloths and bottle brushes — never scourers on plastic.
- Spare tap washers and seals, replaced once a year.