The difference between a relaxed brew day and a long one is almost entirely preparation. Here's a realistic timeline for a 23 litre brew-in-a-bag batch in an urn or all-in-one system, finishing before lunch.

The night before (30 minutes)

  • Check the recipe and print or write a checklist with every step and hop addition.
  • Weigh out the hops, salts and any adjuncts and label them by addition time.
  • Have the grain crushed — buying it already milled for your system saves a job.
  • Clean everything you'll use tomorrow.
  • Fill the urn with treated water and set the timer so it's at strike temperature when you wake up. If your system doesn't have a timer, fill it tonight anyway.
  • Make a yeast starter if you're using liquid yeast for a big beer or a lager.

The day

7:00 — Strike water ready. If it's on a timer, it's already hot. Check the temperature. Sanitise the fermenter and set it aside.

7:15 — Mash in. Stir the grain into the water thoroughly, breaking up every clump. Check the temperature in a few places. Lid on.

7:15 to 8:15 — Mash. This is your free hour. Clean anything you used for weighing, set up the chiller, have breakfast, and check the mash temperature at the halfway point.

8:15 — Lift the bag. Raise it, let it drain, and squeeze it. Take a pre-boil gravity reading.

8:15 to 8:45 — Bring it to the boil. Watch carefully as it approaches boiling, because wort boils over suddenly. While it heats, empty the spent grain and rinse the bag.

8:45 to 9:45 — Boil. Add hops according to your checklist. Set a timer for each addition. Clean as you go — by the end of the boil, the only dirty things should be the urn and the chiller.

9:45 — Flameout and whirlpool. Add whirlpool hops at the right temperature and leave them for 20 minutes. The whirlpool guide explains temperatures.

10:05 — Chill. An immersion or counterflow chiller gets 23 litres to pitching temperature in 20 to 40 minutes, depending on the season.

10:40 — Transfer and pitch. Drain into the fermenter, leaving the sludge behind. Aerate, take an original gravity reading, and pitch the yeast.

11:00 — Clean up. Rinse the urn and chiller while they're still warm, and the residue comes off easily.

11:30 — Done. Put your feet up.

The South Coast summer problem

In January and February, tap water in Nowra can run in the mid-twenties, which means a chiller alone can't get your wort down to 18 °C. Three options:

  • Chill as far as the tap water will go, then put the fermenter somewhere cool, or in a water bath, and pitch once it's down to temperature.
  • Recirculate iced water through the chiller with a small pump and an esky full of ice for the last stage.
  • No-chill. Pour the hot wort into a sealed cube, let it cool overnight, and pitch the next day. It's popular in Australia for good reason, and it shortens the brew day by half an hour. Adjust late hop additions to allow for the extra time the wort spends hot.

Brewing early in the morning also helps. The garage is cooler, and so are you.

Other kinds of brew day

Method Typical hands-on time
Beer kit 30–45 minutes
Fresh wort kit 20–30 minutes
Extract with steeped grains and a hop boil 1.5–2 hours
Brew in a bag 4–4.5 hours
Three-vessel all grain with a sparge 5–6 hours

Where time disappears

  • Heating water — use a timer, or start it while you do something else.
  • Chilling — invest in a chiller, or go no-chill.
  • Hunting for things — lay everything out the night before.
  • Cleaning up at the end — clean during the mash and the boil instead.

A brew day isn't a race, and plenty of brewers enjoy stretching it out. But if you want your afternoon back, preparation is the secret.

Things that save the most time

  1. An urn or system with a timer to heat strike water before you get up.
  2. Grain bought already crushed for your system.
  3. A wort chiller, or no-chill into a cube.
  4. A written checklist with every hop addition and its time.
  5. Cleaning as you go during the mash and the boil.